Could you pls clarify if between steps 6 an 7 the unit could be turned off and on again?

Could you pls clarify if between steps 6 an 7 the unit could be turned off and on again?

Are you talking about TheDiggler's 3.1.9 unlock method in post 120?

Should I change something to use it in italy?

These seem like the basic settings:

Line 1 or 2:
nat mapping enable: yes
sip port: 5060
proxy: sip.vira.it
use outbound proxy: no
register: yes
user id: 6969 *****
password: *******
Use Auth ID: no
codec: G711u
use pref codec only: no

SIP:
stun enable: no

Can anyone help this is really frustrating

unfortunatly it is off ebay, i have never connected it but there a good chance it has been from what i read there doesent seem to be a soloution.

Hi guys, after I unlocked the adapter I upgrated to firmware 3.1.6 and tried to save the GPP_K value using VackVonage but the message I get is:"unable to resolve host: ls.tftp.vonage.net". I put in VuckVonage the Macaddress of Pap2 the GPP_K value I found in Provisioning and as domain ls.tftp.vonage.net and of course an output folder.

After I tried to push sipura1001 firmware into my pap2 and in the tftp server the bin file was sent but going into the webaddress it's still linksys3.1.6,how comes?

For what concerne VuckFonage the ping is ok but I get always the same message even if I disabled the windows firewall.

Well I already setted on the upgrade about the firmware. Could be a problem that my firmware version has been upgrated to 3.1.6! If I try a soft resent and unlock it directly using modified sipura1001 firmware?Could be an idea?

Buy a new PAP2 v1 somewhere (such as WallyWorld) and return the old one.

I've bought two new PAPs from Buy.com on June 2006.They came from 3.1.9lsc. Never, I repeat never, connected to internet.
So, I've to wait until next vonage's release!?!??

Stanaphone question. I would like to do the following for Port 1 of PAP2:

1. Configure Stana IN phone number for free incoming phone calls
2. Configure, so stanaphone account (08XXXX) calls can me made and received on Port 1

Can this be done ? Any user experience in doing this would be great !

Thanks in advance

That's simply how Stanaphone works. When configuring your 08xxxx number in the adapter, incoming calls on both your Stana IN number as well as your Stana STANA # (08xxxx) will ring on that line. Outgoing calls to other 08xxxx numbers will work too, and if you've funded your Stanaphone account, outgoing calls to regular phone numbers will work too.

Diggler

I have an issue with stanain number. The line gets a dialtone, but when I call it from my cellphone, it immediately gets connected even if there is no real conection. No rings/no connection at the wrt54gp2 line that I am using. If I pickup the line it just gets a dialtone while the cell phone still shows connected. Any thoughts?

I have a pap2 vonage blocked with fw. 3.1.12 . Never connected to the internet.

I'm following the dingler's method with a laptop. Using the exact method of the dingler's example.

I have everything,the encrypted xml file downloaded from vonage tftp server, TFTP server solar winds, winxp http information server, dhcp & dns server trough winxp ICS. Modified hosts file like the example.
Everything is equal to the dingler's example unblock.

The unblock process stopped me at the firmware downloading part.

The tftp sent the encrypted xml to the pap2. then the pap2 request the other xml but failed, after that the pap2 has to process the firmware, but here is the problem, doesn't process the firmware, doesn't reboot. Stop it there.

excuse me for my english, i'm italian.

now everything is ok... the problem was with the http server..

Now, what firmware do i have to put ?...

i want to download the GPP_K so then is easy to reunblock, right ?

Can someone tell me the difference between PAP2 and PAP2 - NA

Anyone know where to purchase PAP2 NA

A PAP2-NA (which may stand for "Not Associated" or "North America") is a PAP2 which does not have any provider specific information burned into the device. When FACTORY RESETTING a PAP2-NA, it loads true Linksys factory defaults, and the device becomes unlocked.

I'd check Froogle for places.

can I setup PAP2 with a hunt group like feature ?/

hunt group feature: if a call somes on Port 1 and if that port is busy, the call automatically rollsover to Portt 2

Many thanks in advance.

If both ports are registered to the same VoIP provider, and if the VoIP provider supports call hunt, then you can probably do it through the VoIP provider's web-site. Another way to possibly accomplish this is to setup your own Asterisk Box (or Trixbox) and configure call hunt in there.

Any VOIP providers you know who support hunt feature ?
Thanks as always.

I get a linsys pap2 3.1.9Lsc version firmware, I setup everything that needed t o unlock.( follow the steps of TheDiggler's posts)

And after the linksys tftp get the /spa<MAC>.xml, and no fund /xxxx/spa<MAC>.xml, then NTP request and respond from my local

server. The linksys pap2 do not resolve httpconfig.vonage.net , no http connect.
So it mean , it is no way to unlock my pap2 now? Maybe any way .....
Thanks very much

Thanks . So it mean I need wait vonage release new firmware?

If has a way to confirm that the linksys pap2 has connected inernet and has upgraded?

You've boned yourself in the sense that the original (easy) unlock process won't work anymore as the adapter has now been upgraded to firmware 3.1.9 (assuming you left the adapter powered on for a while after performing the factory reset while connected to the internet). As of firmware 3.1.7, USER MODE firmware upgrades are no longer permitted (which was the security hole permitting the original unlock method).

Now, if you've saved the GPP_K value for this adapter from when you first unlocked it, the easiest and fastest way to re-unlock it is to:

1) Download & decrypt your adapter's INITIAL UPDATE config file from Vonage (use VuckFonage to simplify this process)

2) Inside the decrypted config file will be a USER PASSWORD and an ADMIN PASSWORD

3) Assuming your adapter's web-server is disabled (check first), dial into the adapter's IVR interface, enter the command 7932# (that command toggles the adapter's web-server on/off), follow that command w/ the ADMIN PW (obtained in the previous step), and then hit the # key. If the ADMIN PW isn't purely numeric, here's a conversion chart for entering letters and symbols:

4) Once the web interface is enabled, in a web-browser navigate to the PAP2's IP address. (You can find out the IP address using the IVR command 110#).

5) If prompted to login, you may first need to login as "user" (followed by the USER PASSWORD obtained in step #2). No conversion gets applied to passwords in the web-interface.

6) Once logged in as "user," click the link for "Admin" mode. Enter the username "admin" (followed by the ADMIN PASSWORD obtained in step #2). Again, no conversion gets applied to passwords in the web-interface.

7) Assuming the above is successful, go to the PROVISIONING TAB, turn off automatic provisioning. Go to the SYSTEM tab, remove Vonage's DNS servers. Feel free to DOWNGRADE the firmware to 3.1.6 (or lower) so that USER MODE firmware upgrades can be performed.

8) The adapter is now unlocked.

If you haven't saved the adapter's GPP_K value (shame on you), and if you can continue to factory reset the adapter, you can still unlock it using an isolated LAN running your own DNS server mimicing Vonage's TFTP & HTTP servers. This is much more involved, so I'll only go through posting those steps if you feel you need to go this route.

Diggler

How to enable admin web interface?